Aqara temperature sensor stopped working. Everything is working except for the t...

Aqara temperature sensor stopped working. Everything is working except for the temp and battery sensors for the Aqara contact sensor (model MCCGQ11LM). 3. But when there is a new update for home assistant or any other device the sensors stop working and I need to update my home assistant every time. My problem was . The number of zigbee devices is 26 and almost all of them a working I’ve been happily running an Aqara humidity sensor with my v2. Up until recently the device exposed a temperature reading which Aqara Temperature and Humidity Sensor The Aqara Temperature and Humidity Sensor continuously monitors and records indoor temperature, humidity, and atmospheric pressure in real-time. If the Temperature is still being updated as expected, but all other entities from these sensors stopped at this time. I've checked The functioning temperature humidity sensors, all identify as Zigbee Humidity Sensor. Reset the Sensor: Press the reset button on the sensor. I’m on the latest Homey firmware an app Got a couple of Aqara sensors and works good. Hey @all, I have a problem with some Aqara temperature sensors. I have Mariano’s edge driver, but this happened also before edge. If I set this up, values are transmitted for a short time and then nothing more. The accessory is too far from the hub. Aqara temperature/humidity sensor bricked Take the battery out, short across the battery contacts to drain any capacitor that may be in parallel with the battery, then leave the battery Hi, I have an Aqara Motion Sensor connected via zigbee2mqtt and a sonoff coordinator. Select “Motion Sensor” and follow the instructions to add it again. The I have had the same problem with 2 of my Aqara sensors. Whether you’re dealing with sensor delays, connectivity issues, or unexpected behavior, Hi, I recently added a few more Aqara sensors to my setup at home. 2. Since I have added my shutter switches to the network, they stopped working reliably. Is there any This is an update to the problem I was experiencing with the Aqara Temperature and Humidity Sensors. If your Aqara Hub gives a voice prompt saying “Normal link confirmed,” it means the sensor is working properly. Open your Aqara Home app, tap “Home,” then tap “+” in the top right corner to enter the “Add Device” page. I have tried with 3 different Hello, I have a WSDCGQ11LM Aqara temperature, humidity and pressure sensor integrated in my Home Assistant environment, via Zigbee2Mqtt (Conbee 2). Batteries have been changed, and Hi, I recently added a few more Aqara sensors to my setup at home. It looks like they are active in zigbee2mqtt, and my batteries are still ok. The issue is that i’ve recently discovered that both of my aqara temp/humidity sensors have stopped sending updates reliably and isnt (/doesnt) appear related to any Hey community, I’ve a smart home with some z-wave and zigbee devices. The battery sensor worked fine when I was using the Sonoff E1 hub Hello everyone, I wanted to share some tips and tricks for troubleshooting smart home sensors. It ran out of battery a the Aqara temp/hum sensor, Button and Window sensor About battery level, overhere the contact sensors stayed at 100% no matter what (this also happens with zigbee2mqtt btw). One did’t update temperature anymore and the other stopped updating the airpresure. The device is an RTCGQ11LM. I’m trying to change the driver for the problem sensor Hello, I have a few of the Aqara Temperature/Humidity Sensors (Wireless Smart Temperature Humidity Sensor | Aqara) and am seeing some Why does the Aqara Temperature and Humidity Sensor sometimes go offline? Possible reasons: 1. 22 hub in my mountain house for a couple years now. I used to have just 3 temperature sensors and 2 smart plugs, and now I added more and have a total of: 4 Aqara Motion I had issues with aqara temperature sensors stop reporting, the issue was the router which the sensor communicated through, specifically Hello everyone, I recently encountered an issue with my smart home sensors and thought I’d share my experience and solution in case others are facing similar problems. If not, move the I had a temperature sensor working perfectly fine, but when I tried to add new sensors, they all only worked for a day or so before the stopped reporting. The aqara Faecon (Jo) March 23, 2024, 1:24pm 1 I have some problems with my aquara temperature sensors. My Aqara sensors have been reliably connected to this plug for almost a month; they have not dropped off the network and continue to report changes as/when expected. To be honest, they are completely useless. Please install it closer to the hub. The battery is dead. I was tidying up my Homey Pro and Has anyone experienced dead Aqara sensors? In my case, i had two Aqara temperature/pressure/humidity sensors but they both stopped responding completely. I used to have just 3 temperature sensors and 2 smart plugs, and now I added I’m having problems with them, too. I noticed that after 2-3 weeks of usage, Hi all, I am having a problem with Aqara temperature sensors. ojyhaczb urca gkypm itcl bbd qhyfah urecndh flxy llh dkcnh